LTF_Lighting-Fixture Ring

Create unlimited lighting variations with advanced parametric control

Introduction

The PD_LTF_Lighting-Fixture_Luminaire-Ring Family is a powerful, fully parametric Revit family that allows users to create limitless lighting fixture configurations, all at LOD 400. Whether you’re need surface-mounted lights, or suspended fittings with up/down lighting, this family offers unmatched customization and reporting.

In this guide, we’ll walk through:

How to use the family effectively
Key parameters and their functions
Best practices for adjusting emergency symbols, blank plates, and trims
How to leverage its built-in electrical and COBie data

1. Key Features & Improvements

The PD_LTF_Lighting-Fixture_Luminaire-Ring is a complete redesign of its predecessor, incorporating:

✅ Emergency Symbol:

Fully parametric blue emergency symbol with parametrically self-adjustable size, and visibility.

✅ Advanced Height Control & Reporting:

Simplified mounting height parameters.
Height reporting on label.

✅ Error Prevention & Auto-Adjustments:

Prevents input errors (e.g., zero-dimension entries do not break the geometry).

✅ Flexible Installation Options:

Surface-mounted, recessed, or suspended configurations.
Up/down lighting for suspended fittings.

✅ Improved Data & Labels for Coordination:

COBie-compliant parameters.
Asset labels for mounting height, rating, and subtype visibility.

2. How to Use the Family

A. Setting Up the Light Fitting

Load the family into your Revit project.
Place the fixture in the desired position.
Adjust key parameters (explained below) to configure your light.

B. Adjusting Dimensions

Overall Dimensions:
- Diameter: PD_DIM_Diameter1
- Height: PD_DIM_AssetHeight1
Trim Adjustments (for recessed fittings):
- - PD_DIM_Trim1 the thickness of the ring

3. Customizing the Emergency Symbol

Enable the Emergency Symbol
- Set PD_DATe_IsEmergency to Yes (activates visibility).

4. Electrical Properties

This family includes fully parametric electrical parameters to ensure correct load calculations.

The only input required to set up the load is the PD_Date_Current parameter

5. Control Mounting Angle, Heigth & Visibility

A. Mounting Options

Recessed / Surface-Mounted: To adjust the mounting use the PD_DIM_AssetHeight_Offset parameter. Enter ‘zero’ for surface-mounted lights and for recessed lighting type values, which are the same as the depth of the luminaire but negative. If you want the fitting to protrude slightly below the ceiling, use value at least 1 mm less than the fitting depth
Suspended: Enable PD_DATe_IsUplight for uplighting.
Wall-Mounted: Set PD_DIM_Rotate_X to 90°.

B. Adjusting Visibility in Views

Dont worry about View Region Adjustments:
- Instead Enable PD_DAT_ExtendToCeiling1 or PD_DAT_ExtendToFloor1.
- However, first set the correct ceiling height using parameter PD_DIM_CeilingHeight1 – this is project and/or room-specific, typically set from FFL to concrete ceiling slab, alternatively to the suspended ceiling height
Control Clearance Zones for Clash Detection:
- Toggle PD_DAT_IsClearanceVisible1.
- Set clearance height using PD_DIM_ClearanceHeight1 parameter

6. Control Label visibility and parameters

Each luminaire in the family includes a customisable label that provides essential data such as mounting height, type, sub-type, and rating. These labels can be turned on/off and adjusted in position for optimal readability in your Revit views.

A. Label Parameters and Their Functions

Parameter	Function
`PD_DAT_IsNoteHeight1`	Shows or hides the mounting height label.
`PD_DAT_IsNoteRating`	Displays the power rating (e.g., 20W).
`PD_DAT_IsNoteType`	Toggles visibility of the type label (e.g., “AE”).
`PD_DAT_UseType`	Main label parameter, always used. Default example: `"AE"`
`PD_DAT_SubType`	Adds additional categorization if needed.

B. Positioning the Labels

To ensure proper alignment, you can control the label position using:

PD_DIM_OffsetSymbol-X → Moves the label left/right
PD_DIM_OffsetSymbol-Y → Moves the label up/down

These parameters help in fine-tuning the placement.

8. Metadata & Compliance Information

This family includes COBie data, which is essential for compliance. All parameters have been provided, ready to be populated by the user

Summary

The PD_LTF_Lighting-Fixture_Luminaire-Ring Family is a versatile, parametric lighting solution that simplifies project workflows. By leveraging its parametric properties, you can configure any type of light fitting with precision.

🔗 Download the latest version here: Project Design (IO) Ltd

What’s Next?

Want to see a video tutorial? Let us know in the comments! 👇